(untitled)¶
(untitled).
Cited by¶
1 citation across 1 artifact.
Each citation links to the sentence it supports in the citing article.
Domain-specific¶
- Micro-mechanics of failure
- Fiber, matrix and interface constitutive laws and failure criteria are resolved separately, and homogenization and localization assumptions connect constituent, ply, laminate and structure scales.
This sourceFailed constituent envelopes are predicted by MMF but not by Tsai-Wu. ==Basic concepts== The basic concept of the micro-mechanics of failure (MMF) theory is to perform a hierarchy of micromechanical analyses, starting from mechanical behavior of constituents (the fiber, the matrix, and the interface), then going on to the mechanical behavior of a ply, of a laminate, and eventually of an entire structure. At the constituent level, three elements are required to fully characterize each constituent: The constitutive relation, which describes the transient, or time-independent, response of the constituent to external mechanical as well as hygrothermal loadings; The master curve, which describes the time-dependent behavior of the constituent under creep or fatigue loadings; * The failure criterion, which describes conditions that cause failure of the constituent. The constituents and a unidirectional lamina are linked via a proper micromechanical model, so that ply properties can be derived from constituent properties, and on the other hand, micro stresses at the constituent level can be calculated from macro stresses at the ply level. == Unit cell model == thumb|right|300px|alt=Schematic illustration of idealized fiber arrays and their corresponding unit cells|Schematic illustration of idealized fiber arrays and their corresponding unit cells. Starting from the constituent level, it is necessary to devise a proper method to organize all three constituents such that the microstructure of a UD lamina is well-described. In reality, all fibers in a UD ply are aligned longitudinally; however, in the cross-sectional view, the distribution of fibers is random, and there is no distinguishable regular pattern in which fibers are arrayed. To avoid such a complication cause by the random arrangement of fibers, an idealization of the fiber arrangement in a UD lamina is performed, and the result is the regular fiber packing pattern. Two regular fiber packing patterns are considered: the square array and the hexagonal array. Either array can be viewed as a repetition of a single element, named unit cell or representative volume element (RVE), which consists of all three constituents. With periodical boundary conditions applied, a unit cell is able to respond to external loadings in the same way that the whole array does. Therefore, a unit cell model is sufficient in representing the microstructure of a UD ply. == Stress amplification factor (SAF) == Stress distribution at the laminate level due to external loadings applied to the structure can be acquired using finite element analysis (FEA). Stresses at the ply level can be obtained through transformation of laminate stresses from laminate coordinate system to ply coordinate system. To further calculate micro stresses at the constituent level, the unit cell model is employed. Micro stresses \sigma at any point within fiber/matrix, and micro surface tractions t at any interfacial point, are related to ply stresses \bar{\sigma} as well as temperature increment \Delta T through: : \begin{array}{lcl} \sigma_{\mathrm{f}}&=&M_{\mathrm{f}}\bar{\sigma} + A_{\mathrm{f}}\Delta T\\ \sigma_{\mathrm{m}}&=&M_{\mathrm{m}}\bar{\sigma} + A_{\mathrm{m}}\Delta T\\ t_{\mathrm{i}}&=&M_{\mathrm{i}}\bar{\sigma} + A_{\mathrm{i}}\Delta T \end{array} Here \sigma , \bar{\sigma} , and t are column vectors with 6, 6, and 3 components, respectively. Subscripts serve as indications of constituents, i.e. {\mathrm{f}} for fiber, {\mathrm{m}} for matrix, and {\mathrm{i}} for interface. M and A are respectively called stress amplification factors (SAF) for macro stresses and for temperature increment. The SAF serves as a conversion factor between macro stresses at the ply level and micro stresses at the constituent level. For a micro point in fiber or matrix, M is a 6×6 matrix while A has the dimension of 6×1; for an interfacial point, respective dimensions of M and A are 3×6 and 3×1. The value of each single term in the SAF for a micro material point is determined through FEA of the unit cell model under given macroscopic loading conditions. The definition of SAF is valid not only for constituents having linear elastic behavior and constant coefficients of thermal expansion (CTE), but also for those possessing complex constitutive relations and variable CTEs. == Constituent failure criteria == === Fiber failure criterion === Fiber is taken as transversely isotropic, and there are two alternative failure criteria for it: a simple maximum stress criterion and a quadratic failure criterion extended from Tsai-Wu failure criterion: : \begin{array}{lcl} \text{Maximum stress failure criterion:}-X^\prime_{\mathrm{f}} The Coefficients involved in the quadratic failure criterion are defined as follows: : F_{11} = \cfrac{1}{X_{\mathrm{f}}X^\prime_{\mathrm{f}}}\ ,\ F_{22} = F_{33} = \cfrac{1}{Y_{\mathrm{f}}Y^\prime_{\mathrm{f}}} : F_{44} = \cfrac{1}{S_{\mathrm{f}4}^2}\ ,\ F_{55} = F_{66} = \cfrac{1}{S_{\mathrm{f}6}^2} : F_{1} = \cfrac{1}{X_{\mathrm{f}}} - \cfrac{1}{X_{\mathrm{f}}^\prime}\ ,\ F_{2} = F_{3} = \cfrac{1}{Y_{\mathrm{f}}} - \cfrac{1}{Y_{\mathrm{f}}^\prime} : F_{12} = F_{21} = F_{13} = F_{31} = -\cfrac{1}{2\sqrt{X_{\mathrm{f}} {X}_{\mathrm{f}}^\prime Y_{\mathrm{f}}Y_{\mathrm{f}}^\prime}}\ ,\ F_{23} = F_{32} = -\cfrac{1}{2Y_{\mathrm{f}}Y_{\mathrm{f}}^\prime} where X_{\mathrm{f}} , X_{\mathrm{f}}^\prime , Y_{\mathrm{f}} , Y_{\mathrm{f}}^\prime , S_{\mathrm{f}4} , and S_{\mathrm{f}6} denote longitudinal tensile, longitudinal compressive, transverse tensile, transverse compressive, transverse (or through-thickness) shear, and in-plane shear strength of the fiber, respectively. Stresses used in two preceding criteria should be micro stresses in the fiber, expressed in such a coordinate system that 1-direction signifies the longitudinal direction of fiber. === Matrix failure criterion === The polymeric matrix is assumed to be isotropic and exhibits a higher strength under uniaxial compression than under uniaxial tension. A modified version of von Mises failure criterion suggested by Christensen is adopted for the matrix: : \begin{array}{lcl} \cfrac{\sigma_{Mises}^2}{C_{\mathrm{m}}T_{\mathrm{m}}} + \left(\cfrac{1}{T_{\mathrm{m}}} - \cfrac{1}{C_{\mathrm{m}}}\right)I_1 = 1 \end{array} Here {T}_{\mathrm{m}} and {C}_{\mathrm{m}} represent matrix tensile and compressive strength, respectively; whereas \sigma_{Mises} and {\mathrm{I}}_1 are von Mises equivalent stress and the first stress invariant of micro stresses at a point within matrix, respectively. === Interface failure criterion === The fiber-matrix interface features traction-separation behavior, and the failure criterion dedicated to it takes the following form: \begin{array}{lcl} \left(\cfrac{\left\langle{t}_{n}\right\rangle} \right)^2 + \left(\cfrac \right)^2 = 1 \end{array} where {t}_{n} and {t}_{s} are normal (perpendicular to the interface) and shear (tangential to the interface) interfacial tractions, with {Y}_{n} and {Y}_{s} being their corresponding strengths. The angle brackets (Macaulay brackets) imply that a pure compressive normal traction does not contribute to interface failure. == Further extension of MMF == === Hashin’s Failure Criteria === These are interacting failure criteria where more than one stress components have been used to evaluate the different failure modes. These criteria were originally developed for unidirectional polymeric composites, and hence, applications to other type of laminates and non-polymeric composites have significant approximations. Usually Hashin criteria are implemented within two-dimensional classical lamination approach for point stress calculations with ply discounting as the material degradation model. Failure indices for Hashin criteria are related to fibre and matrix failures and involve four failure modes. The criteria are extended to three-dimensional problems where the maximum stress criteria are used for transverse normal stress component. The failure modes included in Hashin's criteria are as follows. # Tensile fibre failure for σ11 ≥ 0 # Compressive fibre failure for σ11 0 # Compressive matrix failure for σ22 + σ33 0 # Interlaminar compression failure for σ33 Ha, S.K., Jin, K.K. and Huang, Y. (2008). Micro-Mechanics of Failure (MMF) for Continuous Fiber Reinforced Composites, Journal of Composite Materials, '42'(18): 1873–1895.
- Fiber, matrix and interface constitutive laws and failure criteria are resolved separately, and homogenization and localization assumptions connect constituent, ply, laminate and structure scales.
Verification¶
This reference passed the adversarial substantiation pipeline: it was checked to exist and to support the claim it is attached to. See how references were verified.
Registry ID ref:b174a09ec4d8 · see in the full table